鍍鋅板表面絲印移印油墨
概述:MPL系列是針對印刷高亮光產品之表面印刷而開發的油墨,屬雙組份,高亮光,在加入5-10% 專用固化劑后,印刷品附著力更優,可通過百格、耐膠粘及指刮測試。
本信息已過期,發布者可在"已發商機"里點擊"重發"。
MPL系列是針對印刷高亮光產品之表面印刷而開發的油墨,屬雙組份,高亮光,在加入5-10% 專用固化劑后,印刷品附著力更優,可通過百格、耐膠粘及指刮測試。
[通用性]:可用于絲印,移印(需添加相應的溶劑)
[印刷范圍]:電鍍制品(鍍鋅、鍍銀、鍍金、鍍鈦)、金屬制品、玻璃等硬質塑料有良好的附著力。
[性能特點]:高亮光(可提供啞光型),高硬度,雙組份,色澤鮮艷,流平性好,高遮蓋力,耐溶濟,附著力優。
[干燥條件]:
1、自干,表干需15-30分鐘,實干需3小時以上(因氣候及印刷環境不同有差異),測試在油墨干燥后48小時后進行
2、烘烤:100-120度烘干及風干15-20分鐘,可達完全干透,60-80度烘干及風干30-40分鐘,可達完全干透
[技術參數]:
檢驗項目
檢驗結果
測試條件
油墨細度
≤8um
刮板細度計
干膜光澤
≧85°
60°鏡面光澤劑
附著力
100/100
1mm×1mm×100格 3M膠紙剝離
耐 磨 性
無變化
500g/5cm2負載含砂橡皮×200次來回
耐酒精性
無變化
500g/ cm2 負載99.5﹪酒精棉×500次來回
耐堿性
無變化
浸泡5%NaOH×24Hr
耐鹽性
無變化
浸泡5%NaC1×24Hr
耐水性
無變化
浸泡自來水×96Hr
耐熱性
無變化
250℃×5ETc
[使用方法]:a. 使用前請將油墨充分?jǐn)嚢杈鶆,以防止油墨中添加的助劑可產生分離現象。
b. 印刷前有必要可首先考慮除去印刷表面的油漬及塵埃。
c. 請根據作業實際環境條件合理選取本公司之配套稀釋劑。
d. 請根據印刷的理想效果,正確選取合適網版:250-380目網紗的網版,膠刮:65-90度耐溶劑膠刮。
[注意問題]:
a. 本系列油墨必須搭配一定比例的硬化劑才能反應成膜,按主劑/硬化劑5-10%比例配制并攪拌均勻后,好是先固化10分鐘,再行添加稀釋劑以調整到印刷粘度。
b. 本系列油墨可選擇自干或烘烤兩種干燥方式,待工件冷卻后再行測試;自干需待印刷后24或48小時測試。
c. 不同的干燥方式需要的固化時間差異較大,其表現出來的涂膜性能也有一定差異,請根據自身實際條件確立優秀方式。
d. 多色套印時,初底層及中間層只需表干即可印刷下一顏色,后一色印完后,建議加熱固化。
e. 25℃條件下混入硬化劑后油墨可使用時間為6Hr,超過此時限,品質將有所影響,建議每批次配制量以六小時內用完為準。
以上油墨經SGS檢測符合歐盟ROSH標準.
敬告:以上資料記載為本公司實驗室資料數據,僅供參考,不作擔保和承諾,請?jiān)诔浞譁y試后加以使用。The MPL series is developed for printing on the surface of high gloss printing products. It has two components and high gloss. After adding 5-10% special curing agent, the adhesion of printed matter is better. It can be tested through 100 gram, sticky and finger scraping.
[generality]: can be used for screen printing, imprinting (to add the corresponding solvent)
[printing range]: electroplated products (galvanized, silver, gold-plated, titanium plating), metal products, glass and other hard plastics have good adhesion.
[Characteristics]: Gao Liangguang (available in matte), high hardness, two-component, bright color, good leveling, high covering power, solvent resistance, excellent adhesion.
[dry condition]:
1, self drying, it takes 15-30 minutes to dry the table. It takes more than 3 hours (different weather and printing environment). The test is done 48 hours after the drying of the ink.
2, baking: 100-120 degrees drying and air drying for 15-20 minutes, up to completely dry, 60-80 degrees drying and drying for 30-40 minutes, up to completely dry
[technical parameters]:
Inspection project
Test results
Test conditions
Ink fineness
Less than 8um
Scraper fineness meter
Dry film gloss
More than 85 degrees
60 degree mirror gloss agent
adhesion
100/100
1mm x 1mm x 100 lattice 3M adhesive paper stripping
Wear resistance
unchanged
500g/5cm2 loaded sand rubber * 200 times back and forth
Alcohol resistance
unchanged
500g/ cm2 load 99.5 alcohol cotton * 500 times back and forth
Alkali resistance
unchanged
Soak 5%NaOH x 24Hr
Salt tolerance
unchanged
Soak 5%NaC1 x 24Hr
Water resistance
unchanged
Soak the tap water and 96Hr
Heat resistance
unchanged
250 c * 5ETc
[use method]:a. before use, please stir well the ink well, so as to prevent the addition of additives in the ink to produce separation.
It is necessary to first consider the removal of oil stains and dust on the printed surface before B. is printed.
C. please select the company's supporting diluent according to the actual environmental conditions.
D. according to the ideal effect of printing, select suitable screen: 250-380 mesh screen mesh, squeegee squeegee of solvent: 65-90.
[attention problem]:
A., this series of ink must be matched with a certain proportion of hardeners to form the membrane. According to the ratio of the main agent / hardener 5-10%, it can be prepared for 10 minutes before adding the diluent to adjust the printing viscosity.
B. This series of ink can be selected to dry or bake two drying methods, when the workpiece is cooled and tested again; self drying needs to be printed 24 or 48 hours after the test.
C. different drying methods need different curing time. The film performance is also different. Please establish excellent ways according to their actual conditions.
D. polychromatic printing, the first floor and the middle layer only need to print the next color, after the first color printing, it is recommended heating curing.
When E. is mixed with hardener at 25 C, the time of use of ink is 6Hr, which will affect the quality beyond this time limit. It is recommended that the volume of each batch should be used within six hours.
The above ink is tested by the European Union ROSH standard by SGS.
Notice: the above records for the company laboratory data for reference only, not a guarantee and promise, please be used in full after the test.
[本信息來自于今日推薦網]
- ks888888發布的信息
- 金屬電鍍件表面移印油墨
- 涂層表面具有優異附著力,自干型。 主要用途: 各種氨基烘漆面,部分電鍍層面,UV漆面等硬化涂層。...
- 五金電鍍件表面絲印油墨
- 1、適用材料:適合各種ABS、亞克力、PC等注塑硬膠制品或金屬、電鍍表面的絲英移印字符。 2、油墨特性:屬于二液型油墨,流平性好,中度光澤,可絲英移櫻...
- 五金電鍍件表面移印油墨
- 【油墨特性】 雙液型,為通用性的金屬印刷油墨,屬熱烘性的金屬油墨,可絲印也可移印 【適用材料】 不銹鋼、鋁合金等各種金屬材料...
- 鍍鎳板表面絲印移印油墨
- 油墨特點:自干型、低味、油墨色彩鮮艷、墨層豐滿、用途廣泛,具有附著力強,良好的印刷性能,印刷后不需烘干,15-30分鐘表干、24-30小時實干。...
- 鍍鉻板表面絲印移印油墨
- 產品適用范圍: 各類金屬、合金、不銹鋼、玻璃制品、陶瓷、熱固性塑料、UV,電鍍涂層、各種硬化涂層等制作之工業招牌 使用方法:...
- PU漆面PU漆表面絲印移印油墨
- 本產品用了特種混合樹脂與顏料細制研磨加工組合而成的,具有多功能特點,應用范圍廣。該產品特性:亮光、遮蓋力高、附著力佳、耐酒精、耐白電油、耐摩擦。...
油墨重發信息
- 英國禾大芥酸酰胺ER-CH 塑料開口劑 油墨爽滑劑
- 上;厥账臍溥秽珒r(jià)格公司電話
- 上;厥毡┧岙愋刘ス倦娫
- 水性油墨里印表印水性聚氨酯樹脂
- 瑞士zehntner ZND2053及其他型號六角油墨膜厚片
- PTFE粉----油墨改性添加劑
- 回收二手油墨生產線
- PCB三防漆測厚儀 電路板UV膠厚度測量儀 油墨測厚儀
- 油漆油墨遮味劑除味劑
- 超細二氧化硅 白炭黑廠家直銷 品質高誠信為本
- 醋酸異丙酯 涂料溶劑、印刷油墨溶劑
- 印刷機710-0546油墨濾芯
- TPU聚氨酯油墨油漆涂料用樹脂6715 6703 6778
- 新疆 木鈉-木鈉廠報價報價
- 水性油墨用潤濕流平劑